What Doesnt My Front Facing Camera Work On My Iphone 6s Plus

The iPhone 4S has a great camera that tin capture amazing photos, so if that camera stops working, information technology's a pretty large deal. If the damage isn't covered by AppleCare or insurance, information technology can also exist a costly problem. Luckily, a DIY repair is possible, and isn't likewise difficult. It'll only take you around 20-30 minutes and toll yous less than $60, which makes information technology a great option for anyone out-of-warranty and non considering a new phone.

Follow along and we'll get your iPhone 4S photographic camera back in working lodge in no fourth dimension.

Disclaimer: As with any repair, iMore cannot be held responsible for any damage you lot may do to your device. It'due south likewise worth considering that opening up your device to perform any repair or modification can and will void your Apple tree warranty. If you don't experience comfortable opening your device, don't. Use extreme care and caution when performing a repair on any device.

What you lot'll demand to DIY replace an iPhone 4S rear camera

iMore recommends using only quality and genuine parts from a reputable supplier like iFixYouri. They have quality parts, tools, and much more for all your repair needs.

• Replacement photographic camera assembly
• five-point security screwdriver
• Standard #000 Phillips screwdriver
• Spudger tool
• Razor bract
• iSesamo Opening tool (not necessary but awesome for prying up cables and getting nether adhesive)

Ability off your iPhone 4S

Earlier performing any repair yous should always power off your device before opening it upward.

Remove the dorsum plate

1. Using your security screwdriver, remove the 2 screws on either side of the dock connector port.

2. Gear up them bated. They are both the verbal same size and length so it does not thing if you mix them up. They are interchangeable.
3. Gently slide upwardly the back plate by applying a bit of pressure along the lesser with your thumbs and sliding upwards.

4. Now lift off the back plate and set information technology aside.

Remove the bombardment and grounding clip

1. Using your #00 Phillips screwdriver, remove the two screws belongings the battery in place.

2. These screws are different lengths so make sure y'all retrieve which 1 goes where. The i that is slightly larger is the bottom screw.
3. There is a tiny grounding clip underneath the battery prune where the commencement spiral is located. Utilize your spudger tool or finger to remove it earlier prying the prune up. Many times it can go flying if you don't remove information technology first and then you lot'll take difficulty locating it and so it'southward best to remove it starting time.

4. Now use your spudger tool and at the bottom of the battery clip, gently pry upwards so the clip pops up.

5. Move to the edge of the iPhone where the volume buttons are located and use your spudger tool to advisedly pry up the battery. It is stuck downward with a skilful amount of adhesive so be conscientious when prying upward that you don't curve the battery. This is why I practice not use the plastic tab that is provided. It typically rips or bends the battery. If ane part is resistant motion your pry tool a trivial further downwardly and gently start prying it up in different places taking intendance non to come too shut to the volume push cables towards the summit.

6. Once you've gotten the battery pulled out of the iPhone 4S we can move on to inserting the replacement battery.

Remove the acme logic board shield

The camera cable is protected by the top argent logic lath shield. To replace it, we'll need to remove that shield for a few minutes.

1. Remove the iv screws labeled in the motion-picture show beneath using your #00 Phillips screwdriver making certain you lot retrieve which screw came from where every bit they are all different sizes.

2. Use your spudger tool to carefully pry upwardly the shield. There is a tiny clasp at the bottom of the shield. You'll need to brand certain y'all push the top of the shield downwardly a scrap and so it slides out. Once it does you can pull the shield out of the iPhone.

3. Set the shield aside for a few minutes.

Replace the rear camera assembly

1. The photographic camera is continued in the upper left manus corner by only one flex cablevision. Employ your spudger tool to gently pry the camera off the logic board.

2. Remove the defective camera assembly from your iPhone 4S.

3. Now position the new camera assembly into the iPhone and snap it down to the logic lath.

Replace the top logic lath shield

Now that the new photographic camera associates is secured into place on the logic board, we tin can go alee and replace the shield.

1. You will notice that there are little teeth on the left manus bottom side of the shield. These slip into the shield on the left side of the logic board. Line them up and carefully identify back down the shield.
2. Make certain the clasp to the right lower side of the logic board is also positioned underneath the cables and into the groove. All the screw holes should also be lined up at this point.

3. Apply your #00 Phillips screwdriver to replace the four screws you lot removed previously.

Replace the battery and grounding clip

1. Pay attention to how the cablevision is bent on your old bombardment and if the new one is not crimped in the same way put the folds in it before inserting information technology into the iPhone 4S.

2. Line up the grounding clip y'all removed previously over the screw hole earlier snapping down the battery.

3. Snap down the battery in place to the logic board and and so position the battery and press downwardly firmly to brand sure the adhesive sticks.
4. Replace the 2 screws you removed in a prior step starting with the top one using your #00 Phillips screwdriver. Brand sure the grounding clip stays positioned. Use your other hand to agree information technology direct while you supercede the top screw if y'all demand to.

5. Now replace the bottom screw.

Supersede the back plate

1. To replace the back plate line up the hinges around the edges. It should fall right into place. There volition be a gap at the bottom.

2. Using slight pressure slide the encompass down into place with your thumbs. If there is resistance make sure the hinges are lined up correctly and don't force it down and you can easily snap the hinge if it'southward caught up on something.
3. In one case the back cover is securely in place and flush with the antenna band, replace the two screws on either side of the dock connector using your security screwdriver.

And ...done!

That's it. Now that you've finished reassembling your iPhone 4S you lot can go ahead and ability it on. Pop into the camera app and exam the new photographic camera to make sure information technology's performance correctly. That's all there is to it. Now get dorsum to taking all those amazing pictures.

Source: https://www.imore.com/how-replace-rear-facing-camera-iphone-4s

Posted by: biondohuriturnar.blogspot.com

Share this post